Chip Carving
Contents |
Introduction
This form of wood carving involves the use of knives and chisels to remove small chips from the surface of a piece of wood. It can be used to decorate existing objects, easily drawing intricate designs with limitless possibilities.
It is advisable to use hard and high-quality wood for chip carving, as designs tend to look better in such materials. For experts, oak is the classic and traditional wood for carving. Beginners, however, are advised to work with wood that contains softer grain, such as lime, as it is easier to work with.
It is advisable to make cuts along the grain of the piece of wood to ensure fibres don’t tear at the cut line. A depth of 1/8” is the recommended maximum for the chipping cuts, and the chips should be carefully removed so they do not damage the wood. Cutting away from the previous chip ensures smooth removal.
Choosing a knife
A knife with a thin, wedge shape will allow for precise cuts.
For beginners, one knife will allow the creation of simpler designs. This knife should have a cutting edge as parallel to the handle as possible, as this will be easier to use.
Other knives may have a cutting edge in a rectangular shape, ideal for stabbing, and knives with a fine point that permit delicate woodwork. A knife with a round cross-section can be manipulated more easily, allowing the creation of more natural lines.
Gripping the knife
Gripping the knife correctly is vital if the cuts are to be made correctly and the design faultless. The back of the knife should be gripped with the fingers, and the thumb placed on a flat side that can be found on the front of the handle, under the blade. Keeping the thumb on the hand is crucial to preventing injury.
Another grip involves placing fingers on the front of the handle and the thumb on the back of the blade.
Both grips require that cutting is done at a 65° angle.
Pattern transfer
Creating intricate designs can be achieved by transferring patterns to a piece of wood of approximately 3/4” and 3/8” thickness. It is necessary to sand down the surface that is receiving the transference, as sanding dulls the designs after the carving process.
Graphite paper can be used to transfer designs to oddly shaped woods or, if preferred, a photocopy of a design can be placed against the wood. With an iron at medium temperature, the design is easily transferred as printer ink is heat sensitive.
Three corner chip technique
The wood should be placed either on the lap or on a table if is too big to be handled.
The first step is to use a plunge cut, involving a piercing motion into the wood at a 65° angle. Starting from where the plunge cut was made, a slicing cut should then be performed. Starting at a shallow depth, it should deepen until it reaches the depth of the plunge cut. The last step is to perform another slicing cut similar to the first one, in order to create a triangle. The piece of wood should pop out easily.
--G&S Specialist Timber 10:12, 06 Dec 2016 (BST)
Find out more
Related articles on Designing Buildings Wiki
Featured articles and news
About the 5 Percent Club and its members
The 5% Club; a dynamic movement of employers committed to building and developing the workforce.
New Homes in New Ways at the Building Centre
Accelerating the supply of new homes with MMC.
Quality Planning for Micro and Small to Medium Sized Enterprises
A CIOB Academy Technical Information sheet.
A briefing on fall protection systems for designers
A legal requirement and an ethical must.
CIOB Ireland launches manifesto for 2024 General Election
A vision for a sustainable, high-quality built environment that benefits all members of society.
Local leaders gain new powers to support local high streets
High Street Rental Auctions to be introduced from December.
Infrastructure sector posts second gain for October
With a boost for housebuilder and commercial developer contract awards.
Sustainable construction design teams survey
Shaping the Future of Sustainable Design: Your Voice Matters.
COP29; impacts of construction and updates
Amid criticism, open letters and calls for reform.
The properties of conservation rooflights
Things to consider when choosing the right product.
Adapting to meet changing needs.
London Build: A festival of construction
Co-located with the London Build Fire & Security Expo.
Tasked with locating groups of 10,000 homes with opportunity.
Delivering radical reform in the UK energy market
What are the benefits, barriers and underlying principles.
Information Management Initiative IMI
Building sector-transforming capabilities in emerging technologies.
Recent study of UK households reveals chilling home truths
Poor insulation, EPC knowledge and lack of understanding as to what retrofit might offer.